preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 1 of 8 www.qorvo.com product description the QPL6216 is a high linearity, ultra - low noise gain block amplifier in a small 2x2 mm surface - mount package. at 2332 mhz, the amplifier typically provides +3 6 dbm oip3. the amplifier does not require any negative supplies for operation and can be biased from positive supply rails from 3.3 to 5.25 v. the device is housed in a lead - free/green/rohs - compliant industry - standard 2x2 mm package. the QPL6216 uses a high performance e - phemt process. the low noise amplifier contains an internal active bias to maintain high performance over temperature. functional block diagram package: dfn, 8 - pin 2 .0mm x 2.0mm x 0.85mm feature overview ? high gain device C typical value 1 5 .5 db ? ultra - low noise figure, 0. 4 5 db nf at 2332 mhz ? high linearity, +3 6 dbm output ip3 ? high input power ruggedness, >22 dbm pin, max ? unconditionally stable ? externally controlled icq with vbias ? integrated shutdow n control pin ? 3 .3 - 5 .25 v positive supply voltage: ?vgg not required applications ? sdars active antenna ordering information part number description QPL6216sb 5 piece sample bag QPL6216sq 25 piece sample bag QPL6216sr 100 piece 7 reel QPL6216tr7 2500 piece 7 reel QPL6216pck - 01 evaluation board + 5 pc sample bag standard t/r size = 2500 pieces on a reel ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 2 of 8 www.qorvo.com absolute maximum rat ings storage temperature - 65 to 150 c supply voltage (v dd ) +7 v rf input power, cw, 50, t = 25c +22 dbm electrical specifications at +25 ? c test conditions unless otherwise noted: v dd = + 4.5 v, v b ias = +3.6v, temp =+25c, 50 system note: 1) noise figure data has input trace loss de - embedded 2) icq set by external 2.7 5 k resistor parameter rating units parameter min typ max units supply voltage (v dd ) +3. 3 + 4.5 + 5.25 v bias voltage (v b ias ) +3. 3 +3.6 +5.25 v t case ? 40 + 10 5 c t j (for >10 6 hours mttf) + 190 c parameter conditions min typ max units operational frequency range 2320 2332 2345 mhz gain 14 . 0 15.5 16 . 5 db input return loss 9 db output return loss 15 db output p1db +18.0 +2 2.5 dbm output ip3 pout=+2 dbm/tone, f=1 mhz +3 0 +36 dbm noise figure 1 0.45 0.65 db power shutdown control (pin 6) on state 0 0.63 v off state (power down) 1.17 1.8 v dd v current, i dd 2 on state 45 60 75 ma off state (power down) 3 4 ma shutdown pin current, i sd v pd 1.17 v 140 a thermal resistance, jc channel to case 62 c/w recommended operating conditions ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 3 of 8 www.qorvo.com application schematic ? vbias=3.6v icq 40ma 50ma 60ma 70ma 80ma vdd=4.5v r3 5.5k 3.7k 2.75k 2.13k 1.73k
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 4 of 8 www.qorvo.com pin configuration and de scription performance plots C QPL6216 - pcb test conditions unless otherwise noted: v dd = 4.5v, v bias = 0.45v, f 0 = 2332 mhz , temp = +25c . noise figure data has input trace loss de - embedded. pin no. label description 1 vbias sets the icq bias point for the device. 2 rf in rf input pin. a dc block is required. 6 shut down a high voltage (>1.17v) turns off the device. if the pin is pulled to ground or driven with a voltage less than 0.63v, then the device will operate under lna on state. 7 rf out / dcbias rf output pin. dc bias will also need to be injected through a rf bias choke/inductor for operation. 3, 4, 5, 8 nc no electrical connection. provide grounded land pads for pcb mounting integrity. backside paddle rf/dc gnd rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance; see pcb mounting pattern for suggested footprint. ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 5 of 8 www.qorvo.com ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 6 of 8 www.qorvo.com mechanical information marking: part number C 6216 trace code C xxxx notes: 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 220, issue e (variation vggc) for thermally enhanced plastic very thin fine pitch quad flat no lead package (qfn). 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 9 5 - 1 spp - 012. ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 7 of 8 www.qorvo.com pcb mounting pattern notes: 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 4. ensure good package backside paddle solder attach for reliable operation and best electri cal performance. ?
preliminary QPL6216 high - linearity sdars lna data sheet rev e subject to change without notice 8 of 8 www.qorvo.com product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1b value: passes 500 v to < 1000v test: human body model (hbm) standard: js - 001 esd rating: class c3 value: passes 10 00 v to <2 000v test: charged device model (cdm) standard: js - 002 msl rating msl rating: level 2 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 solderability compatible with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) soldering processes. package contact plating: nipdau this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). rohs compliance this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free \ contact information for the latest specifications, additional product information, worldwide sales and distribution locations : tel: 1 - 844 - 890 - 8163 web: www.qorvo.com important notice the information contained herein is believed to be reliable; however, qorvo makes no warranties regarding the information con tained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. all informatio n contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for qorvo products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. this information does not constitute a warranty with respect to the products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usag e of trade or otherwise, including the implied warranties of merchantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo products are not warranted or authorized for use as critical componen ts in medical, l ife - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury o r death. copyright 2016 ? qorvo, inc. | qorvo is a registered trademark of qorvo, inc. email: customer.support@qorvo.com ?
|
